EasyScreen Solutions
CONCEAL, PROTECT AND UTLITISE
POWDER COATED TO MATCH ANY COLOUR SCHEME
Conceal unsightly plant machinery with the sharp clean lines of the Screen Wall. Easy and quick to install, with our ClassicScreenWall solution, there’s no cutting required and it integrates aesthetically with surrounding architecture.
Perfect for a wide range of industrial applications including:
- Large condensor platform screening
- General architectural screening
- Compressor enclosurer and screening
- Other mechanical plant equipment enclosures
With Screens at 1200mm, 1600mm, 2000mm or 2400mm high, with custom heights available.
COMPLIANCE & TECHNICAL INFORMATION
Australian Standards: AS1170.1, AS1170.2, AS1657 & AS1664.1 & Relevant Clauses of the Building Code of Australia
Lightweight at 7kg/m2
Standard Heights: 1200mm, 1600mm, 2000mm & 2400mm
Open Space: 18.75% (custom spacing available on request).
Classic ScreenWall can be sized to suit any plant equipment allowing sufficient area around the units for access (available in any length to suit your needs).
Wind Loads: Con-form Group products have been certified for wind regions A, B and C.
V500 = 45m/s – Region A – Tc 2.5
V500 = 57m/s – Region B – Tc 2.5
V500 = 66m/s – Region C – Tc 2.5
All components are backed by a 25 year warranty.
FAQS
The complete Con-form Group product range is backed by a 25-year warranty barring the Phantom Screen which is covered by a 10-year warranty.
As there are so many varied units with different mounting configurations, our certification does not cover this aspect, hence we do not provide fixings for air-con units – our recommendation is to bolt the units down to the mesh (with a piece of AVANT Anti-Vibration, Anti-Noise Technology pad between them) using a plate with a hole in it, below the mesh or to bolt through the mesh and cross beam, if the mounting foot of the units is directly above it.
If the complete platform is required on the roof in one package, a crane would be required – the alternative is to cut the package open and carry the individual parts up.
A 13mm spanner which is supplied with the fixings, a drill and a tek driver.
A 3m x 3m platform would take one person 2 hours at their first attempt.
The square meter size of the platform x 250Kg – providing the weight is centralised on the platform – the structural design of the platform ensures that a centrally located weight on the platform is evenly distributed over the footprint size of the platform.
Total weight (combined) of Platform, Screens, Louvers etc (*²Refer to weights below), plus any plant equipment (platform area in m² x weight of platform) + weight of plant equipment)/ platform area in m²
Example of a typical scenario:
6 m x 6 m EasyMech MR platform, with 2000 kg unit:
Platform = 36m²
Platform weight = 14 Kg/ m² @ 3 Degrees
(36 x 14)+2000)/36 = 70kg per m²
Less than 1% of platforms sold by Con-form Group have required the roof to be penetrated to fix the platform down. Each wedge comes with a self-adhesive strip of foam rubber or VHB tape which, as the foam rubber compresses, acts as a dissimilar metals barrier, waterproofing element and sound & vibration barrier.
For our Metal Deck HVAC platforms, we evaluate our fixing methods based on the pitch, location and roof sheet profile. To view our range of fixings (including siesmic fixings), click the button below to download our EasyFix Specification Sheet.
In order to get a price on one of our HVAC / Mechanical Plant Platforms, we need some information. If you’re looking for DIY Solution, head on over to our shop, where you can purchase our off-the-shelf solutions.
For a custom job, we need to know the roof pitch in degrees and the approximate size of the platform required (in 600mm increment sizes). Or provide us with information on the size of the unit that will be installed and where the access panels are on the unit (if space is required on these sides to provide for maintenance access), and we can provide you with a quote.
Contact our team today.
Specify EasyScreen Classic
System shall be Con-form Group ClassicScreen, proprietary item number ESCS6516 secured to either one of Con-form Group’s EMMRS1, EMMRS3, EMMRGX, EMCRA, EMCRGX, ESSTRMR, ESSTRCR or ESSTSP solutions.
100% VISUAL BARRIER, 55% AIRFLOW (can be increased)
Increase air-flow to improve machine performance and improve longevity of your machines. We can guarantee 100% visual barrier to your HVAC units with minimum 55% airflow thanks to our flexible Louvre System (airflow can be increased as required).
We have two Louvre Systems (both provide minumum 55% airflow):
- Weather Profile: Our classic Louvre system
- Storm Profile (pictured right): Ideal for deterring water from getting where you don’t want it.
Like our ClassicScreen Wall system our LouvreWall airflow systems can be powdercoated to match any colour scheme.
COMPLIANCE AND TECHNICAL INFORMATION
Australian Standards: AS1170.1, AS1170.2, AS1657 & AS1664.1 & Relevant Clauses of the Building Code of Australia.
Wind Loads: Wind Loads: Con-form Group products have been certified for wind regions A, B and C.
V500 = 45m/s – Region A – Tc 2.5
V500 = 57m/s – Region B – Tc 2.5
V500 = 66m/s – Region C – Tc 2.5
Aesthetic screening with 55% open air flow & sized to suit any plant equipment. Airflow can be increased to any specification.
Lightweight at 7kg/m2
100mm blade repeats.
Standard heights: 1200mm, 1600mm, 2000mm 2400mm (custom heights available upon request).
Components backed by a 25 year warranty.
Specify EasyScreen Classic
System shall be Con-form Group LouvreWall airflow, proprietary item number ESLW secured to either one of Con-form Groups EMMRS1, EMMRS3, EMMRGX, EMCRA, EMCRGX, ESSTRMR, ESSTRCR or ESSTSP solutions.
FAQS
The complete Con-form Group product range is backed by a 25-year warranty barring the Phantom Screen which is covered by a 10-year warranty.
As there are so many varied units with different mounting configurations, our certification does not cover this aspect, hence we do not provide fixings for air-con units – our recommendation is to bolt the units down to the mesh (with a piece of AVANT Anti-Vibration, Anti-Noise Technology pad between them) using a plate with a hole in it, below the mesh or to bolt through the mesh and cross beam, if the mounting foot of the units is directly above it.
If the complete platform is required on the roof in one package, a crane would be required – the alternative is to cut the package open and carry the individual parts up.
A 13mm spanner which is supplied with the fixings, a drill and a tek driver.
A 3m x 3m platform would take one person 2 hours at their first attempt.
The square meter size of the platform x 250Kg – providing the weight is centralised on the platform – the structural design of the platform ensures that a centrally located weight on the platform is evenly distributed over the footprint size of the platform.
Total weight (combined) of Platform, Screens, Louvers etc (*²Refer to weights below), plus any plant equipment (platform area in m² x weight of platform) + weight of plant equipment)/ platform area in m²
Example of a typical scenario:
6 m x 6 m EasyMech MR platform, with 2000 kg unit:
Platform = 36m²
Platform weight = 14 Kg/ m² @ 3 Degrees
(36 x 14)+2000)/36 = 70kg per m²
Less than 1% of platforms sold by Con-form Group have required the roof to be penetrated to fix the platform down. Each wedge comes with a self-adhesive strip of foam rubber or VHB tape which, as the foam rubber compresses, acts as a dissimilar metals barrier, waterproofing element and sound & vibration barrier.
For our Metal Deck HVAC platforms, we evaluate our fixing methods based on the pitch, location and roof sheet profile. To view our range of fixings (including siesmic fixings), click the button below to download our EasyFix Specification Sheet.
In order to get a price on one of our HVAC / Mechanical Plant Platforms, we need some information. If you’re looking for DIY Solution, head on over to our shop, where you can purchase our off-the-shelf solutions.
For a custom job, we need to know the roof pitch in degrees and the approximate size of the platform required (in 600mm increment sizes). Or provide us with information on the size of the unit that will be installed and where the access panels are on the unit (if space is required on these sides to provide for maintenance access), and we can provide you with a quote.
Contact our team today.
SCREEN TO ROOF, SCREEN TO GROUND, SCREEN TO… SURFACE!
Not limited to our ClassicScreen Wall system, we’ve engineered a solution that allows us to install our LouvreWall and AcousticWall solutions directly to any surface! Metal, concrete and more!
Our screening solutions can be sized to suit any plant equipment allowing sufficient area around the units for access (available in any length to suit your needs).
Weight’s vary depending on selected screen solution and they can be sized to suit any plant equipment allowing for sufficient area around the units for access. Also available in any lengths to suit your needs.
Compliance & Technical Information
Wind Loads: Con-form Group products have been certified for wind regions A, B and C.
V500 = 45m/s – Region A – Tc 2.5
V500 = 57m/s – Region B – Tc 2.5
V500 = 66m/s – Region C – Tc 2.5
Heights include 1200mm, 1600mm, 2000mm 2400mm (custom heights also available).
Weight’s vary depending on selected screen solution.
All components are backed by a 25 year warranty.
Specify our ScreentoRoof Solution
ScreentoRoof MR*: System shall be Con-form Group ScreentoRoof MR, proprietary item number ESSTRMR secured with either SMTDFX, SMKLFX or SMCGSDFX seismic clip fixings in compliance with AS1170.4
ScreentoRoof CR**: System shall be Con-form Group ScreentoRoof CR, proprietary item number ESSTRCR secured with either SMTDFX, SMKLFX or SMCGSDFX seismic clip fixings in compliance with AS1170.4
*MR = Metal Roofs
**CR = Concrete Roofs
FAQS
The complete Con-form Group product range is backed by a 25-year warranty barring the Phantom Screen which is covered by a 10-year warranty.
As there are so many varied units with different mounting configurations, our certification does not cover this aspect, hence we do not provide fixings for air-con units – our recommendation is to bolt the units down to the mesh (with a piece of AVANT Anti-Vibration, Anti-Noise Technology pad between them) using a plate with a hole in it, below the mesh or to bolt through the mesh and cross beam, if the mounting foot of the units is directly above it.
If the complete platform is required on the roof in one package, a crane would be required – the alternative is to cut the package open and carry the individual parts up.
A 13mm spanner which is supplied with the fixings, a drill and a tek driver.
A 3m x 3m platform would take one person 2 hours at their first attempt.
The square meter size of the platform x 250Kg – providing the weight is centralised on the platform – the structural design of the platform ensures that a centrally located weight on the platform is evenly distributed over the footprint size of the platform.
Total weight (combined) of Platform, Screens, Louvers etc (*²Refer to weights below), plus any plant equipment (platform area in m² x weight of platform) + weight of plant equipment)/ platform area in m²
Example of a typical scenario:
6 m x 6 m EasyMech MR platform, with 2000 kg unit:
Platform = 36m²
Platform weight = 14 Kg/ m² @ 3 Degrees
(36 x 14)+2000)/36 = 70kg per m²
Less than 1% of platforms sold by Con-form Group have required the roof to be penetrated to fix the platform down. Each wedge comes with a self-adhesive strip of foam rubber or VHB tape which, as the foam rubber compresses, acts as a dissimilar metals barrier, waterproofing element and sound & vibration barrier.
For our Metal Deck HVAC platforms, we evaluate our fixing methods based on the pitch, location and roof sheet profile. To view our range of fixings (including siesmic fixings), click the button below to download our EasyFix Specification Sheet.
In order to get a price on one of our HVAC / Mechanical Plant Platforms, we need some information. If you’re looking for DIY Solution, head on over to our shop, where you can purchase our off-the-shelf solutions.
For a custom job, we need to know the roof pitch in degrees and the approximate size of the platform required (in 600mm increment sizes). Or provide us with information on the size of the unit that will be installed and where the access panels are on the unit (if space is required on these sides to provide for maintenance access), and we can provide you with a quote.
Contact our team today.
